- 产品特点
- 技术规格
● 单缸、四冲程、油冷、纯电启动发动机
● 采用单缸四气门、SOHC结构:进气阻力小、充气效率高、动力强劲
● 采用指形滚子摇臂、气缸偏心技术:减少功率损失、寿命更长、动力强劲
● 采用离心式油气分离循环技术:废气排放及机油消耗更低
● 采用内置平衡齿、副齿缓冲吸振结构，让振动及齿轮啮合声音更低:声音品质高
● 平衡齿采用磨齿工艺，精度高:啮合声音小
● 离合器采用5组主弹簧、5片大直径摩擦片结构:可选配进口FCC纸基摩擦片、拉杆分离式: 离合器分离更平稳、残余力矩小、分离性更好
● 离合器采用三级减震技术，能有效吸收冲击:齿轮啮合平稳，声音品质及可靠性更高。
● 内置平衡轴结构，大幅降低单缸发动机振动:振动更小、骑乘舒适性好
● 采用加强型主副轴:提升齿轮疲劳强度、延长使用寿命
● 采用中置油冷技术:缸头热负荷更低,可靠性更高
● 初级从动齿采用整体式钢齿轮，强度好
● 采用活塞背冷技术，强制润滑和冷却活塞及活塞环，降低发动机热负荷
● 采用外置纸质精滤器对整机机油过滤，区别于离心式部分过滤结构，热机及各运动副磨损更小:可靠性更高
● 采用专用加强型曲轴与平衡轴轴承:轴承寿命更高，可靠性好
● 采用调整垫片取代调节螺钉方式来驱动气门，点面接触换成了线面接触，磨损更小，气门间隙变化小:减少气门间隙维护
● 采用18滚柱起动超越离合器:起动更可靠
● Single-cylinder, four-stroke, oil-cooled, electric starting engine.
● Adopts single cylinder four valves, SOHC structure :low intake resistance, high inflation efficiency, strong power.
● Use of finger roller rocker arm, cylinder eccentric technology :reduced power loss, longer life, strong power.
● Centrifugal oil and gas separation cycle technology :lower exhaust emissions and oil consumption.
● Built-in balance teeth, auxiliary teeth buffer vibration absorption structure, so that vibration and gear meshing sound is lower :high sound quality.
● Balance tooth grinding process, high precision :small meshing sound.
● Clutch adopts 5 sets of main spring, 5 large diameter friction plate structure :optional imported FCC paper based friction plate, pull rod separation type :more stable clutch separation, small residual torque, better separation.
● The clutch adopts three-stage shock absorption technology, which can effectively absorb shock :smooth gear mesh, higher sound quality and reliability.
● Built-in balance shaft structure greatly reduces single-cylinder engine vibration :less vibration, better riding comfort.
● Enhanced main and counter shafts :to improve gear fatigue strength and extend service life.
● Central oil cooling technology :lower head heat load and higher reliability.
● The primary driven tooth adopts integral steel gear with good strength.
● Using piston back cooling technology, forced lubrication and cooling piston and piston ring, reduce engine heat load.
● The external paper fine filter which is different from the centrifugal partial filter structure, the wear of the thermal engine and various motion pairs is smaller :with higher reliability.
● Special reinforced crankshaft and balance shaft bearings :higher bearing life and better reliability.
● The valve is driven by adjusting gaskets instead of adjusting screws, and the point contact is replaced by line contact, which has less wear and less change of valve clearance :reduces valve clearance maintenance.
● Starting the overrunning clutch with 18 rollers :more reliable starting.
外特性曲线 WIDE OPEN THROTTLE CURVES
悬挂图 INSTALLATION DIMENSIONS